lack of power @ 2500 RPM's - Page 8 - TTORA Forum
Toyota Territory Off-Roaders AssociationToyota Territory Off-Roaders Asso
ciationToyota Territory Off-Roaders Association
     


Go Back   TTORA Forum > Regional Forums > Indiana > Tech
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read


Reply
 
LinkBack Thread Tools
Display Modes
Old 06-16-2010, 07:51 AM   #211 (permalink)
Moderator
 
My Rig: 2005 TACOMA DCSB
Join Date: Mar 2008
Location: CedarTucky
Posts: 4,068
Best of Luck!
NwiTACO is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 06-16-2010, 10:51 AM   #212 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
thanks, I'll hopefully have a progress report by next weekend. the last week or so have been focused on the house projects so no progress since the blower went back on.

At least I know the throttle response is quicker until the motor bogs out.
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 07-15-2010, 04:07 PM   #213 (permalink)
Veteran Member
 
Fuod's Avatar
 
My Rig: '04 TRD 4x4 X-Cab
Join Date: Jan 2007
Location: Evansville
Posts: 1,310
Here you go Bear, and it costs less then everything you've already done!

http://indianapolis.craigslist.org/bfs/1842643134.html


Fuod is offline   Reply With Quote Quick reply to this message
Old 07-15-2010, 04:54 PM   #214 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
man that is so cool!
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 07-15-2010, 08:10 PM   #215 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
7/15/10 update

Well the troops keep marching forward, by the end of the month they should be in Paris....

sorry wrong type of update. LOL

got the TPS in today but still need to "dial" it in. when installing the TPS I found out that you can not just plug and play. there are adjustments that need to be made.

so tomorrow after I go buy an ohm meter, I should be under the hood testing the new Tps and adjust in the idle. according to the one former ford tech and master toyota tech that has been helping me long distance from texas and mississippi, after the adjustments the truck should be running.

If that is the case it will be loaded up...again. for the redbird run on Saturday. As usual, the truck won't be road tested properly but hopefully it will at least see a trail this time out.
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 07-19-2010, 07:30 PM   #216 (permalink)
Moderator
 
My Rig: 2005 TACOMA DCSB
Join Date: Mar 2008
Location: CedarTucky
Posts: 4,068
Soooo....
__________________
Blue Ribbon Coalition #4847

'05 Tacoma DCSB on Tons
NwiTACO is offline   Reply With Quote Quick reply to this message
Old 07-19-2010, 07:33 PM   #217 (permalink)
inttora
 
jason6746's Avatar
 
Join Date: Feb 2007
Location: lafayette in.
Posts: 565
^^ what he said ^^
__________________
2001 tacoma 2.7 5sp.
with some

amsoil dealer
jason6746 is offline   Reply With Quote Quick reply to this message
Old 07-19-2010, 07:41 PM   #218 (permalink)
Veteran Member
 
Fuod's Avatar
 
My Rig: '04 TRD 4x4 X-Cab
Join Date: Jan 2007
Location: Evansville
Posts: 1,310
Quote:
Originally Posted by NwiTACO View Post
Soooo....
Quote:
Originally Posted by jason6746 View Post
^^ what he said ^^
Ditto
Fuod is offline   Reply With Quote Quick reply to this message
Old 07-19-2010, 08:48 PM   #219 (permalink)
Senior Member
 
99sr54wd's Avatar
 
Join Date: Jul 2008
Posts: 285
Quote:
Originally Posted by Bear View Post
got the TPS in today but still need to "dial" it in. when installing the TPS I found out that you can not just plug and play. there are adjustments that need to be made.
.
I don't know what special about it. all I did was drop it in. nothing but 2 screws and a wire harness. that was a year ago. it was throwing cods on and off in a span of 2 months so I went ahead changed it.

my understanding is a TPS is just a step resistor, a very simple sensor.
__________________
99 4Runner, SR5, 3.4L 4WD, 5spd. 265/75/16 Hankook A/T. SS 1.2, Marlin 1200 Clutch, ARB front bumper, BruceTS rear bumper, Tundra Brakes, Brembo rotors, Stubb's HD-SKO sliders.

04 SR5 4.0L 4WD, , Scion H/U, FJC silver Bil' shocks and coils, BFG A/T.

Daily Driver: 2000 Odyssey.
99sr54wd is offline   Reply With Quote Quick reply to this message
Old 07-20-2010, 08:53 AM   #220 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
Tony came over and with the aid of both his scan gauge and code reader. we determined that it was not the new TPS causing the issue.

the code thrown was PO120 which is the TPS "circuit" reading in Tony's FSM. it says it can be one of three problems. the TPS itself, the circuit or wiring harness has an opening (short) in it. or the ECU.

I HATE ELECTRICAL!

I also changed out the check valve on the throttle body put in place to prevent blow back through it from the supercharger, and found a broken connector. I couldn't find the exact type and went with an aftermarket connnector and I think it is resticting vacuum too much now as well. So I am going to have to replumb those vacuum lines also.
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 07-20-2010, 10:07 AM   #221 (permalink)
Veteran Member
 
Fuod's Avatar
 
My Rig: '04 TRD 4x4 X-Cab
Join Date: Jan 2007
Location: Evansville
Posts: 1,310
Is it possible your ECU got wet or something? Maybe a voltage spike?

We had an '86 Ford Taurus when I was a kid that we used to jump start another car, the Taurus never ran right again after that until we had the ECU replaced. Sh!t happens man!
Fuod is offline   Reply With Quote Quick reply to this message
Old 07-20-2010, 11:29 AM   #222 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
Ecu has never had a chance to get wet in the last 10 years. and the one time it did have the chance, it didn't get wet just close.

I am not sure if maybe the ecu crapped out due to the timing box attached to it for the supercharger or what. but I think that maybe the first place I start looking now
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 07-22-2010, 11:40 AM   #223 (permalink)
Senior Member
 
99sr54wd's Avatar
 
Join Date: Jul 2008
Posts: 285
bear,

at this point, if I were you, I would start to look into long term, meaning taking the motor out. it has been a long time you try to solve the engine stumble problem, now for sure you know it's not something simple.

since money, time, garage space are all tight, plus your plan for the new rear linkage, I would, first get rid of the FJ project, free up some money, and space. meanwhile, you are on the road a lot, start to look for parts, hit the junk yarks, specailly the exhaust, ECU and wire loom.

your engine has good compression, so internally is sound. you need to target on the corrosion, plumbing and and electrical.

I saw a lot of crimpped wires, solder is the only way. take out the aux accessories first, keep them in storeage, simplify the circuitry. clean, seal, replace the wires, connectors, harnesses.

sorting out the plumbing, vaccumm lines are hell lot easier when you have the engine on a stand.

one other reason you need to get the engine out is when people beef up the frame, often they forgot about the motor mounts which can kill a lot of things.

my 0.02
__________________
99 4Runner, SR5, 3.4L 4WD, 5spd. 265/75/16 Hankook A/T. SS 1.2, Marlin 1200 Clutch, ARB front bumper, BruceTS rear bumper, Tundra Brakes, Brembo rotors, Stubb's HD-SKO sliders.

04 SR5 4.0L 4WD, , Scion H/U, FJC silver Bil' shocks and coils, BFG A/T.

Daily Driver: 2000 Odyssey.
99sr54wd is offline   Reply With Quote Quick reply to this message
Old 07-22-2010, 01:04 PM   #224 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
Tony, I appreciate you coming over as well as your insight. I agree that I have a lot of electrical "housework" to do. I hate the appearance of all the wires running everywhere. Up until recently I had all that mess buttoned up and looking much cleaner.

as for pulling the motor, I am already making plans to seal up the exhaust as the patch work behind the muffler and around the O2 sensor did not hold. I am also going to change out the vacuum connection we had issues with yesterday. With that issue we couldn't test drive which I wish would have been able to. After that I think the PO120 code may not be such a big issue (not consistant~I can live with it if it only happens once in a while as I suspect it happens)

IF these plans do not solve the issue, then I will seriously consider pulling the motor.

NOt sure what you are saying about the motor mounts though, unless you mean a weak mount will cause the motor to move around excessively. In that regards. the motor is pretty sound. that I have been able to test as I have "rocked" the motor quite a bit wrapping the rev limiter searching for the overall problem.
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 07-22-2010, 02:58 PM   #225 (permalink)
Veteran Member
 
Fuod's Avatar
 
My Rig: '04 TRD 4x4 X-Cab
Join Date: Jan 2007
Location: Evansville
Posts: 1,310
Can't a leaking exhaust lower the exhaust pressure and screw up the intake mixture?

And since the exhaust pressure changes with RPM I could see a good idle but bad performace at driving rpms.
Fuod is offline   Reply With Quote Quick reply to this message
Old 07-22-2010, 04:34 PM   #226 (permalink)
Senior Member
 
99sr54wd's Avatar
 
Join Date: Jul 2008
Posts: 285
Quote:
Originally Posted by Bear View Post
NOt sure what you are saying about the motor mounts though, unless you mean a weak mount will cause the motor to move around excessively.
yep. that's regarding your future plans of beefing up the frame. the factory mounts ain't the strongest and the rust isn't helping either. all frames flex under load. frame flex absorbs some the shocks but when frame got stiffened up, the motor mounts are taking large portion of that shock. probably some of the bushing are already crispy after 15 years.
__________________
99 4Runner, SR5, 3.4L 4WD, 5spd. 265/75/16 Hankook A/T. SS 1.2, Marlin 1200 Clutch, ARB front bumper, BruceTS rear bumper, Tundra Brakes, Brembo rotors, Stubb's HD-SKO sliders.

04 SR5 4.0L 4WD, , Scion H/U, FJC silver Bil' shocks and coils, BFG A/T.

Daily Driver: 2000 Odyssey.
99sr54wd is offline   Reply With Quote Quick reply to this message
Old 07-22-2010, 07:07 PM   #227 (permalink)
Veteran Member
 
Fuod's Avatar
 
My Rig: '04 TRD 4x4 X-Cab
Join Date: Jan 2007
Location: Evansville
Posts: 1,310
Quote:
Originally Posted by 99sr54wd View Post
...frame flex absorbs some the shocks but when frame got stiffened up, the motor mounts are taking large portion of that shock...
I never thought of it that way...

I've realized the same thing in many other projects, just not in a vehicle frame.
Fuod is offline   Reply With Quote Quick reply to this message
Old 07-22-2010, 08:47 PM   #228 (permalink)
Senior Member
 
99sr54wd's Avatar
 
Join Date: Jul 2008
Posts: 285
it's none issue for a daily driver, but on an off road rig, you are working against heavy load, strong impact, age and corrosion. you can make that engine runs like a champ, but if it's not sitting at the right place at the right time lining up with the right things, it's not doing you any good. vibration alone can kill so many things.
__________________
99 4Runner, SR5, 3.4L 4WD, 5spd. 265/75/16 Hankook A/T. SS 1.2, Marlin 1200 Clutch, ARB front bumper, BruceTS rear bumper, Tundra Brakes, Brembo rotors, Stubb's HD-SKO sliders.

04 SR5 4.0L 4WD, , Scion H/U, FJC silver Bil' shocks and coils, BFG A/T.

Daily Driver: 2000 Odyssey.
99sr54wd is offline   Reply With Quote Quick reply to this message
Old 07-23-2010, 08:47 AM   #229 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
yes, a leaky exhaust can cause low back pressure, effecting the Hp.

in my case the exhaust leak did not start until after I changed out the o2 sensor and muffler so I can't really see that being the original issue. But it will be addressed soon regardless. It's a cheap fix in the scope of things and it is only responsible, "green" speaking.
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 07-28-2010, 10:33 PM   #230 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
7/28/10:

picked up a new vacuum connector today. When I replaced the check valve that was installed in conjunction with the supercharger. I found this "y" connector that goes between the heads that leads up to the throttle body was cracked and broken.

I tried replacing it with a generic aftermarket tee, but the truck will not run as the generic is too restrictive.

Although I did get a Po120 code which is the TPS circuit code. I am hoping that it was a fluke from just changing out the TPS and that this vacuum line crack has been a contributor to the problems.

Here is the basis to my reasoning. 1)When first installing the supercharger,I had to wait to install the check valve connnected to this line. When the line did not have the check valve, the truck ran similar to how it runs now, just not as excessive as it is currently. 2) even though vacuum lines have been checked repeatedly since this problem started. This "y" connnector lies in an area on the manifold that is hard to get to and even harder to see. So this could have been repeatedly overlooked.3) These vacuum lines have effected the performance of the motor so severely that the truck will barely idle as is.4) this connector lies in an area that excessive heat has caused this plastic part to become brittle over time. the vacuum lines do not move per sey, but when the motor warms up the crack could have changed, opening & closing which would have resulted in the truck running good after start up and then poorly once the motor warms up. Which is exactly how the motor operates currently.

So as soon as I get the chance I will change out the vacuum lines. Unlike most vacuum lines though these are not easy to get to. they are on the back side of the top of the motor, buried under the wire harness for the supercharger and injectors. The vacuum port for the drivers side can't even be seen and can only be accessed by feel.

IF this does not effect a positive result, and against Tony's suggestion of rebuilding th motor (which is out of the budget for quite some time) I will remove the TCM 1.1 timing controller from the Ecu. and remove the wire taps employed by the TCM. This should resolve the Po120 code as I think I narrowed downn where the short/open condition would be.
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 09-24-2010, 11:12 AM   #231 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
Latest update on BearAttack is: It is still sick! While Andrew was up working on his bumpers, He did have a little time to check some sensor readings and check the coil packs with a spare that he brought with him. So far everything checked out.

I completely removed the TCM 1.1 module off the Ecu and soldered the wires where the taps were placed.

The spark plugs were also checked again for new plugs they had too much carbon build up on them. WE got another set of stock NGK's and discovered the bosche plugs installed by a shop I had taken it to were somewhat shorter than the NGK's. Although the truck did not restart afterwards, it did sound like it was getting a better ignition.

The latest guess is the fuel regulator. although I am pretty sure we already replaced it when at Harlan last year. I am going to swap it out for an aftermarket adjustable inline regulator. What is not making sense is when it does run, at first start up, it acts as if it is getting too much fuel (rich condition) but then begins running lean. The plugs also show evidence of runnng rich by the carbon build up on the plugs.

I am also concerned about discovering an electrical connection hanging down by the transmission. But can not find anywhere it might plug into. The thought on it is that it is actually a "dead" connection from the factory for an automatic transmission. but I have yet to be abe to confirm Toyota actually did that sort of thing as other manufactures will do.
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 09-28-2010, 08:42 AM   #232 (permalink)
Brian
 
brinner's Avatar
 
Join Date: Mar 2007
Location: Kentucky
Posts: 2,016
I think this might help











.
brinner is offline   Reply With Quote Quick reply to this message
Old 11-10-2010, 04:16 AM   #233 (permalink)
inttora
 
jason6746's Avatar
 
Join Date: Feb 2007
Location: lafayette in.
Posts: 565
any updates?
__________________
2001 tacoma 2.7 5sp.
with some

amsoil dealer
jason6746 is offline   Reply With Quote Quick reply to this message
Old 11-10-2010, 07:49 AM   #234 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
I have been letting the motor sit. Instead I have been cleaning up a few other issues such as suspension, exhaust etc.

I decided to redo the fuel cell and currently it is preventing me from even starting the truck. But hopefully once I get that back in order the few adjustments we made to the throttle body will make the truck a lot better.
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 12-07-2010, 10:00 AM   #235 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
update!


there is no updatibale progress, without a garage, the temps are too cold to work on it. and Even if the weather permitted, the wallet wouldn't allow it.

I did get the throttle position sensor installed and dialed in, I'm in the process of moving the fuel lines around on the fuel cell again but will have to wait. I also moved some springs around but the front end needs new springs to get the shackle off the frame. Once I do that, I'll have to put a spring back in the rear pack to level the truck out unless I go ahead and convert the rear over to the link set up.

but the motor hopefully will respond to the TPS being recalibrated

Oh and my new odessey battery Sulfiated again (condition of sulfation) so a new one will be needed and I've already been told they will not warrantee the second one.
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 01-03-2011, 08:56 PM   #236 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
The new "to do list"

1) remove fuel cell to "re-plumb"/ install original fuel cap back on (tired of taking 30 minutes to fill the fuel cell up)
2) re-fill front diff after building new cover
3) replace back brake line (I'm the only person I know that can break a brake line without even moving the vehicle out of the driveway.
4) test drive the hell out of the truck to see if last theory of TPS actually fixed the truck
5) replace battery
6) various other minor crap, I can't think of right now.

The truck feels like I am getting closer to having it running again...but I have felt that feeling before so my hopes are not that high.
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 04-29-2013, 09:56 PM   #237 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
Wow 4-3-2011

That was the date I started this thread.I'm not sure when the last post was made, but it appears this thread can now die quietly into the depths of totally played out threads! It definitely appears the longest fuster cluck in the history or I don't know when is over!!!!

The truck finally drove (WITH UNSEEN POWER) today!!!

The only remaining real problems are the steering system needs to be bled from putting a new hydro assist ram on and the brakes bled from having to replace the master cylinder due to it sitting so long.

I can break down things later if need be but now I must go make some money so I can pay for all the mods I have dreamt of for the last three years!

Happy days! & cheers!
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 04-30-2013, 05:49 AM   #238 (permalink)
Moderator
 
My Rig: 2005 TACOMA DCSB
Join Date: Mar 2008
Location: CedarTucky
Posts: 4,068
Seems like we have heard this before...jk

Hhope you got rid of all those gremlins once and for all! Please gimme the 'skinny on the remedy whenst you get a chance. Good news for sure!

2-12-2009 til 4-30-2013
NwiTACO is offline   Reply With Quote Quick reply to this message
Old 04-30-2013, 08:36 AM   #239 (permalink)
Veteran Member
 
Bear's Avatar
 
My Rig: 1997 Toyota Tacoma
Join Date: Dec 2004
Location: state of confusion
Posts: 11,173
Quote:
Originally Posted by NwiTACO View Post
Seems like we have heard this before...jk

Hhope you got rid of all those gremlins once and for all! Please gimme the 'skinny on the remedy whenst you get a chance. Good news for sure!

2-12-2009 til 4-30-2013
Oh! I whole heartly agree and had my reservations about declaring the issues to be in the past, but I am extrememly confident the "bugs" at 2500 rpm's are exterminated!i feel this way due to the most successf test drives I have ever been able to perform with the most power the truck has ever demonstrated for the longest duration. Not to mentioned one of the test drives was BEFORE ripping the ignition wires apart over a month ago and the again yesterday!

I'll try to muster up enough guts to eat the crow by giving the entire 411 the next time I'm awake. But right now I just happened to wake up from my post employment slumber long enough to notice the email alert that you repsonded to my post
__________________
BEAR
OVERKILL IS AN UNDERRATED ACHIEVEMENT

Originally Posted by abbott
remember, in the world of cars and trucks, its not cubic inches, its cubic dollars.
GO SPURS GO!!!!
Bear is offline   Reply With Quote Quick reply to this message
Old 04-30-2013, 09:03 AM   #240 (permalink)
Moderator
 
My Rig: 2005 TACOMA DCSB
Join Date: Mar 2008
Location: CedarTucky
Posts: 4,068
__________________
Blue Ribbon Coalition #4847

'05 Tacoma DCSB on Tons
NwiTACO is offline   Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the TTORA Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Insurance
Please select your insurance company (Optional)

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
2002 Tacoma 2wd Prerunner lack of rear braking power.... tomytum Early Tacoma Tech 4 01-04-2009 10:05 PM
random lack of power!! Portman Early Tacoma Tech 1 06-04-2008 07:35 AM
lack of power? Spacecwboy Pickup/Early 4Runner Tech 1 11-11-2007 08:37 AM
for the lack of a bigger truck masternayte Pickup/Early 4Runner Tech 1 08-25-2006 12:00 AM
Lack of Power scottdeane Performance/Engine/Exhaust 7 08-15-2006 12:09 PM

» Premium Vendor Showcase
» Recent Discussions
POWERTRAX LOCK-RIGHT...
02-25-2015 09:15 AM
Last post by JTSDIFFS
Today 12:12 PM
6 Replies, 923 Views
Gattora.com Domain...
Today 11:19 AM
by *Darcy*
Last post by *Darcy*
Today 11:19 AM
0 Replies, 39 Views
2016 4x4 V6...
Today 10:32 AM
Last post by ChargersSB
Today 10:32 AM
0 Replies, 14 Views
Bomber basher
07-15-2016 12:40 AM
Last post by Brake Weight
Yesterday 03:45 PM
2 Replies, 148 Views
Team Associated SC10
08-13-2016 01:07 AM
Last post by Brake Weight
Yesterday 03:43 PM
1 Replies, 55 Views
Toyota 8.4 Diamond Axle
08-26-2016 09:45 AM
Last post by BigRonDog
Yesterday 12:36 PM
2 Replies, 119 Views
Random Video Thread
07-10-2006 01:31 PM
by Tweeter
Last post by mountainguyed67
Yesterday 11:11 AM
631 Replies, 63,929 Views
G144 Rear Third Member...
08-28-2016 09:14 PM
by Percy
Last post by Percy
08-28-2016 09:14 PM
0 Replies, 53 Views
ARB Air Compressors at...
02-11-2016 12:17 PM
Last post by JTSDIFFS
08-28-2016 06:34 PM
3 Replies, 243 Views
ARB Air Compressors at...
02-11-2016 12:16 PM
Last post by JTSDIFFS
08-28-2016 06:33 PM
3 Replies, 243 Views
» Buyer's Resource
Powered by vBadvanced CMPS v3.2.3

All times are GMT -6. The time now is 12:48 PM.




Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2016 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2016 DragonByte Technologies Ltd.