TRD axle swap - TTORA Forum
 
LinkBack Thread Tools Display Modes
post #1 of 11 (permalink) Old 02-17-2005, 11:01 PM Thread Starter
Senior Member
 
Join Date: Dec 2004
Location: Flagstaff, AZ
Posts: 485
TRD axle swap

looked around on the board a bit and couldn't seem to find much. Anyhow, what all do I need to swap in a TRD rear axle besides the axle and switch?THanks

Ryan
SAStoy is offline  
Sponsored Links
Advertisement
 
post #2 of 11 (permalink) Old 02-17-2005, 11:28 PM Thread Starter
Senior Member
 
Join Date: Dec 2004
Location: Flagstaff, AZ
Posts: 485
I noticed just a few posts below had a similar question, only addition that I read besides the axle and switch is the Locker ECU. Is this just the 4wd computer? Anything else?

Ryan
SAStoy is offline  
post #3 of 11 (permalink) Old 02-18-2005, 12:02 AM
Senior Member
 
The Shocker's Avatar
 
Join Date: Jan 2005
Location: Virginia
Posts: 132
I'm doing mine March 12. Doc Sausage seems to know about the swap if you can find him.
The Shocker is offline  
post #4 of 11 (permalink) Old 02-18-2005, 12:15 AM Thread Starter
Senior Member
 
Join Date: Dec 2004
Location: Flagstaff, AZ
Posts: 485
Quote:
Originally Posted by The Shocker
I'm doing mine March 12. Doc Sausage seems to know about the swap if you can find him.

Thanks, I will keep an eye out for him. Anyone else familiar with parts needed for the swap? Thanks

Ryan
SAStoy is offline  
post #5 of 11 (permalink) Old 02-18-2005, 07:24 AM
Senior Member
 
P1michaud's Avatar
 
Join Date: Jan 2005
Location: New Brunswick, Canada
Posts: 230
Talking TRD axle swap

Quote:
Originally Posted by SAStoy
Thanks, I will keep an eye out for him. Anyone else familiar with parts needed for the swap? Thanks Ryan
Ryan,
Let's start by getting a bit more info. What year, model, engine is your truck?
What is your gear ratio, real important unless you plan on re-gearing the front as well? Are you going to buy a complete E-locking rear drum to drum?

I would suggest you do the install in 3 steps as follows:
1-Build your wiring harness/control module (i.e. have all the electronics sorted out before you start) and do some bench testing to make sure it all works. I spent about 6 to 8 hours doing the actual wiring and testing not counting the time spent rounding up supplies for this step.

2-Prepare the e-locking rear for installation then install it on the truck. This includes changing the diff oil, making sure the brakes are in good working order and all your seals don't seem to be leaking (all you can do there is a visual inspection unless you want to completely dismantle the new e-locking rear). Next install it on your truck. Just follow the link in my signature and I have a buch of pictures of the swap. Pretty straight forward. You might want to consider having some spare u-bolts for the leaf packs, rubber bump stops if yours are missing or bad as well as some spare brake lines. Don't forget the spare brake fluid. I spent about 3 hours preparing the new rear and another 4 to 5 doing the actual swap again not not counting the time spent rounding up supplies for this step.


3-Install the wiring harness/control module on your truck.
This step took the longest for me because I wanted everything to look professional and did not want to have to mess arround with this 3 months down the road. I spent about 8 hours installing all the wiring and control module.

Quote:
Originally Posted by SAStoy
Locker ECU. Is this just the 4wd computer? Anything else?
The locker ECU is just a control module for the e-locker. It's a relatively simple module and you could easily make one if need be. Do a search on youatech.com and you should find lots of wiring diagrams for the e-locker.

Anyhow, let me know if you have any more questions
And good luck with the install.
Cheers,
P

1999 Canadian Tacoma with a few goodies.
Pics here !
P1michaud is offline  
post #6 of 11 (permalink) Old 02-18-2005, 07:27 AM
Senior Member
 
P1michaud's Avatar
 
Join Date: Jan 2005
Location: New Brunswick, Canada
Posts: 230
Here is a link with some wiring diagrams to help you along:
http://www.yotatech.com/showthread.p...=wiring+locker

1999 Canadian Tacoma with a few goodies.
Pics here !

Last edited by P1michaud; 02-18-2005 at 07:30 AM.
P1michaud is offline  
post #7 of 11 (permalink) Old 02-18-2005, 10:34 PM Thread Starter
Senior Member
 
Join Date: Dec 2004
Location: Flagstaff, AZ
Posts: 485
Quote:
Originally Posted by P1michaud
Ryan,
Let's start by getting a bit more info. What year, model, engine is your truck?
What is your gear ratio, real important unless you plan on re-gearing the front as well? Are you going to buy a complete E-locking rear drum to drum?

I would suggest you do the install in 3 steps as follows:
1-Build your wiring harness/control module (i.e. have all the electronics sorted out before you start) and do some bench testing to make sure it all works. I spent about 6 to 8 hours doing the actual wiring and testing not counting the time spent rounding up supplies for this step.

2-Prepare the e-locking rear for installation then install it on the truck. This includes changing the diff oil, making sure the brakes are in good working order and all your seals don't seem to be leaking (all you can do there is a visual inspection unless you want to completely dismantle the new e-locking rear). Next install it on your truck. Just follow the link in my signature and I have a buch of pictures of the swap. Pretty straight forward. You might want to consider having some spare u-bolts for the leaf packs, rubber bump stops if yours are missing or bad as well as some spare brake lines. Don't forget the spare brake fluid. I spent about 3 hours preparing the new rear and another 4 to 5 doing the actual swap again not not counting the time spent rounding up supplies for this step.


3-Install the wiring harness/control module on your truck.
This step took the longest for me because I wanted everything to look professional and did not want to have to mess arround with this 3 months down the road. I spent about 8 hours installing all the wiring and control module.



The locker ECU is just a control module for the e-locker. It's a relatively simple module and you could easily make one if need be. Do a search on youatech.com and you should find lots of wiring diagrams for the e-locker.

Anyhow, let me know if you have any more questions
And good luck with the install.
Cheers,
P
Well, the truck is a 98 Tacoma with a 3.4 and an auto. I will be getting the complete rear axle but am having some trouble understanding exactly what you meant by building my own ECU. How do I do this? I was wondering if I could just get the ECU out of the rig I am pulling the axle from. Let me know. Thanks


RYan
SAStoy is offline  
post #8 of 11 (permalink) Old 02-19-2005, 07:01 PM
Senior Member
 
P1michaud's Avatar
 
Join Date: Jan 2005
Location: New Brunswick, Canada
Posts: 230
Thumbs up More info

Quote:
Originally Posted by SAStoy
Well, the truck is a 98 Tacoma with a 3.4 and an auto.
In that case I would suggest doing a search about axle codes on this website and yotatech.com to determine what gear ratio your have. Like The Shocker pointed out start with this web page: http://home.4x4wire.com/erik/diffs/ If all else fails use the "spin and count" method. Easily done for peace of mind to confirm the info you find on line. I also belive that the more common gear ratio is 4:10.

Quote:
Originally Posted by SAStoy
I will be getting the complete rear axle but am having some trouble understanding exactly what you meant by building my own ECU. How do I do this? I was wondering if I could just get the ECU out of the rig I am pulling the axle from. Let me know.
Again refer to this webpage: http://home.4x4wire.com/erik/diffs/ and look at the pic at the bottom of the page. This is an electrical schematic of the ECU and you can easily build your own. This webpage: http://www.4x4wire.com/toyota/tech/electric_locker/ also talks about it. If you can get the ECU out of the donor rig by all means do so!
Cheers,
P

1999 Canadian Tacoma with a few goodies.
Pics here !
P1michaud is offline  
post #9 of 11 (permalink) Old 02-19-2005, 10:20 PM
Senior Member
 
Join Date: Dec 2004
Location: NC
Posts: 460
Send a message via AIM to RENEGADE76254
i got a prerunner and considered this on my truck but found the cost to me more than i was able to invest. yet i am very interested in how it works out for you, keep us posted on ur developments if u dont mind and best of luck.

-SLIM-

1999 TOYOTA TACOMA PRERUNNER
RENEGADE76254 is offline  
post #10 of 11 (permalink) Old 02-20-2005, 09:34 PM Thread Starter
Senior Member
 
Join Date: Dec 2004
Location: Flagstaff, AZ
Posts: 485
Quote:
Originally Posted by RENEGADE76254
i got a prerunner and considered this on my truck but found the cost to me more than i was able to invest. yet i am very interested in how it works out for you, keep us posted on ur developments if u dont mind and best of luck.

How much were you looking at to do the swap?
SAStoy is offline  
post #11 of 11 (permalink) Old 02-20-2005, 09:49 PM
Senior Member
 
Join Date: Dec 2004
Location: NC
Posts: 460
Send a message via AIM to RENEGADE76254
the average price i got from junkyards for the rear axle with 4.10 like i currently have was about $700 w/o brake drums, and then wirring harness and accesories would be about $50+ and then sum even claimed i could not remove the axle myself b/c of insurance.... anyhow i have other stuff i want more than that, plus i make just enuf to make my truck payments, i dont need to spend no more than is neccesary.

-SLIM-

1999 TOYOTA TACOMA PRERUNNER
RENEGADE76254 is offline  
Reply
Gear in this thread - Powered by O'Reilly Auto Parts

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the TTORA Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome