Everyting for sale - cheap...

[mad_african]

Here is the list of what I need to off load.... Please send interest email to partsforsale@uys.com or post offers here.

1 set 15" bead lock rings (for 1 steel wheel - welding required) - $ 50
Rick 1 90% tread 35" GY MTR on 15" bead lock wheel - $ 150
set of 4 Tacoma OEM steel wheels with new 235/75/15 Tempest tires - $ 100
Toyota Tacoma A/C Compressor - $ 50
2.7 Intake manifold - $ 30
2.7 fuel rail with injectors - $ 80
2.7 throttle body - $ 50
Tacoma stock Skid Plate (front) - $ 35
Tacoma stock Skid Plate (rear) - $ 20
1 set Tacoma V6 struts incl springs - $ 35
Lower A arms w ball joints - $ 30
2 sets Stock Tacoma front Upper control arms - $ 20
Front diff 95.5 - 1998 Tacoma (non-ADD) 3:73 - $ 80
Rear 3rd 95.5 - 2002 non TRD locker 3:73 - $ 100
Toyota 8" 3rd member diff 3.90 gear ratio - $ 50
2 Tacoma Rear axle shafts with break drum assy's (Driver side) - $ 50 each
Steering wheel w/o air bag - $ 10
Tacoma T-case flange (rear) - $ 15
Tacoma T-Case flange (front) - $ 15
2005 V6 Stainless steel factory exhaust w/ muffler - $ 75
2005 V6 Air Filter - $ 5
2005 V6 Air intake assy - $ 50
1 set 95.5 - 00 break calipers (non - ABS) - $ 25
Tacoma Rubber door seal driver side - $ 10
New Power steering pump for 2.4 & 2.7 - $ 80
Tacoma 3:91 gears rear - $ 20
Tacoma 3:91 gears front - $ 20
Tacoma 3:58 gears front - $ 20
FZJ80 4:10 rear 9.5" gears - $ 40
Tacoma steering column with column shifter for auto 2WD - $ 10
guage cluster 95.5 - 1998 Tacoma & 4runner - $ 10
Tacoma Drivers side door (no dings - black w/ grey interior) - $ 150
Rear cab liner (single cab Tacoma - grey) - $ 10
Tacoma Glove box (grey with latch) - $ 10
Tacoma bolt in cross member for tranny & T-case - $ 20
Tacoma 95.5 - 2004 rear bumper (chrome) - $ 25

[STOMPER]

How much for the bead locks the 5 with the one that needs welding? I doubt I have the funds to get them but it never hurts to ask.

I found some 16 bolt rings I may buy but I will still have to drill 16 more holes cause I want some 32 bolt rings.

[mad_african]

How much for the bead locks the 5 with the one that needs welding? I doubt I have the funds to get them but it never hurts to ask.

I found some 16 bolt rings I may buy but I will still have to drill 16 more holes cause I want some 32 bolt rings.
The new unused set you were interested in just sold, sorry man. The bead locks I have left are the ones that came off the buggy, used. Set of 5 including hardware... LMK if you're interested.

[STOMPER]

:D The new unused set you were interested in just sold, sorry man. The bead locks I have left are the ones that came off the buggy, used. Set of 5 including hardware... LMK if you're interested.


Damn!!!! I guess Ill go with the Areo one and be a Guinnie pig.

[mad_african]

Updated the list with a price guide - let me know if any of this stuff appeals to you.

L8er

[Marshytaco]

Jack,
PM me your address so I can get you some funds in the mail to hold those rims for me.
Thanks!
Marshall

[sloppytaco]

I am interested in the:
Front diff 95.5 - 1998 Tacoma (non-ADD) 4:10 - $ 80

[mad_african]

I have PM'd both of you.. Marshy and Sloppy.... Thanks.

[crawlrunner]

The rear 3rd 4:10 'non TRD locker' ... is it open or what locker is installed?

[crawlrunner]

And, that front 4:10 gear set will also work in my '99 Taco?? What mfr? Will this be enough change for 32s because my stock 3:58s are killin' me ... and my clutch w/31s? Are you going to compete in UROC?

[Blitanicle99]

I dunno about if the gears will work but 4:10s with a manual and 32s will be a an improvement. I want 4:56s for my 33s and im 5spd. I hate my 4:10s with my tires. Ive honestly considered going back to 31s with my gears. I hate it that much. I could damn fit 35s but with my gear ratio id tear up a clutch in a week.

[mad_african]

And, that front 4:10 gear set will also work in my '99 Taco?? What mfr? Will this be enough change for 32s because my stock 3:58s are killin' me ... and my clutch w/31s? Are you going to compete in UROC?
Hey Ed,

The Rear 3rd non-TRD locker means it is open and without the Electric locker option - sorry I did not explain that properly in the origional post.

The gearing issue you have. I also had the origional 3:58 gears and went to 4:56's which allowed me to run 35's with the speedo almost dead on again. Changing to 4:10's in your truck would give you the ability to run 33's with a slight under read on your speedo and a slight over read using 31's. Your and my transfer case ratio's are different from those that came from the factory with 4:10's. The 4:10 gears I have are origional factory toyota (I doubt they are Precision Gear or any major brand name for that matter)
Hope that answers some of your questions.

The front diff I have has 4:10's already setup in it from the factory, so if Sloppytaco wants your front housing as a spare instead, you can just pop this one in without having to re-gear yours. (Just a thought).

YES - I am hoping to be able to compete in UROC next year, just don't know if I'm going to make it.

[sloppytaco]

Ed,
Like what Jack said above about the front diff. I am going to use it to change the gears to 4.88's the 4.10's will not be used. Let me know if you want to buy the diff and when you get it in I can buy your diff.

[sloppytaco]

I can use the:
Driver side Tacoma Rack Tie rod end - $ 10

[crawlrunner]

Chris /Jack

That sounds great to me! I'll take both 3rds. Let me know what I need to do Jack.

LLLLLLLLLater

[crawlrunner]

Jack,

If there is any way, I'd like to somehow help with your UROC quest. At 6'-5" & +250lbs I got your 'buggy steadying' spotter leverage!!!!!

LLLLLLLLater

[mad_african]

I can use the:
Driver side Tacoma Rack Tie rod end - $ 10
It's yours for a whopping $10 plus $500000000 shipping LOL

you can PayPal me or pay me when you see me. How soon do you need the part - do you need me to ship etc. etc. PM me if you don't mind.

Jack

[mad_african]

Chris /Jack

That sounds great to me! I'll take both 3rds. Let me know what I need to do Jack.

LLLLLLLLLater
I will PM you when I get home tonight. Thanks for your offers and I'll chat with you later.

Jack

[synovus]

The upper control arm ball joints are new? If so, I'll take 'em.

[mad_african]

The upper control arm ball joints are new? If so, I'll take 'em.

They came off of a 2004 double cab and have very low miles/use. If you still want them I'll pay shipping.

Jack

[synovus]

They came off of a 2004 double cab and have very low miles/use. If you still want them I'll pay shipping.

Sounds good, Jack. What's your preferred method of payment? Paypal?

[link817]

hey jack, i'm meeting up q/ synovus this weekend, give steveo the control arms and i'll deliver them.

[mad_african]

Sounds good, Jack. What's your preferred method of payment? Paypal?
PayPal to jackj@uys.com or ebay@uys.com - it will be under the name UYS Enterprises. I will get my personal assistant to physically deliver them to you.

Thanks, I appreciate the purchase.
Regards
Jack

[synovus]

PayPal to jackj@uys.com or ebay@uys.com - it will be under the name UYS Enterprises. I will get my personal assistant to physically deliver them to you. Thanks, I appreciate the purchase. Regards Jack

Payment sent. :)

[synovus]

hey jack, i'm meeting up q/ synovus this weekend, give steveo the control arms and i'll deliver them.

It's actually just the ball joints. Thanks for offering to deliver 'em, though! That would be very cool and convenient. By the way, check my Kings thread. I posted a message to you there yesterday, regarding meeting this weekend. Lemme know what you think.

Rick

[mad_african]

Payment sent. :)
Payment recieved - Thanks. I'll send them along with Christian...

Thanks to Christian for offering.

[Marshytaco]

Jack,
I will be paypaling you some of the money for the wheels in a day or two, or maybe early next week. I figured that would be easier than mailing it. I just have to wait for the deposits to show up from ebay so I can use my checking account instead of my CC and they said that takes 2-3 days. If you would rather me not us PP for any reason please let me know ASAP by calling me or PMing me.
Thanks again!
Marshall

[mad_african]

Bump pity bump...

I'm back and in selling mode again.... LOL