2 piece drive shaft

[Captkirkyota]

SOLD


http://img.photobucket.com/albums/v420/captkirkyota/temp/P2240001.jpg
75.00 The rear half has been beefed up stronger than stock. Needs a carrier bearing. You can get one from 20 - 80 bucks depending on where you call. I went thru it because my rear springs are really soft and have terrible axle wrap. Did not know this till after I went to a one piece otherwise I would have shortened the front when I put in my crawler.

[Captkirkyota]

Bump, was 150.00 now 75.00

[SPooN]

Assuming this is for a 2001?

[Captkirkyota]

Yes
Assuming this is for a 2001?

[TBob]

will this work with a 6" trailmaster lift?

http://img.photobucket.com/albums/v420/captkirkyota/temp/P2240001.jpg
75.00 The rear half has been beefed up stronger than stock. Needs a carrier bearing. You can get one from 20 - 80 bucks depending on where you call. I went thru it because my rear springs are really soft and have terrible axle wrap. Did not know this till after I went to a one piece otherwise I would have shortened the front when I put in my crawler.

[Heatstroke]

Hey Kirk, I'd take that and the steering pump for $110.00 ($75 + $35). That will give me 2 spare of each. lmk.

[Captkirkyota]

Hey Kirk, I'd take that and the steering pump for $110.00 ($75 + $35). That will give me 2 spare of each. lmk.
Sold.
Do you remember where I live? Or do you wanna meet?

[Heatstroke]

Don't really remember. I can pick up, we could meet, or if you are coming to meet n greet we could exchange then. What ever works.

[Captkirkyota]

Don't really remember. I can pick up, we could meet, or if you are coming to meet n greet we could exchange then. What ever works.
Prolly won't go to meet n greet. I can meet you pretty much any day this week but Tues.
I have all hours open right now since my semi is in shop, so you make the call, I will be there.

[Heatstroke]

Let me see how my week is shaping up tomorrow. Boss is in town so it could be coo-koo. I got junk to do Wed, Fri, Sat, Sun for sure. So Thursday could work. I'll pm or give you a holler. Thanks.

[Captkirkyota]

Let me see how my week is shaping up tomorrow. Boss is in town so it could be coo-koo. I got junk to do Wed, Fri, Sat, Sun for sure. So Thursday could work. I'll pm or give you a holler. Thanks.
No problem, I just found out my semi is gonna cost almost 11k to get fixed and it won't be ready till Sat. mid morning, so I can even come over to you at work on your lunch break if you'd like, even tues as long as it is before 3pm.

[Heatstroke]

Ouch!! 11K, OUCH!! A dollar or two in loose change might be in order for a Powerball ticket ($240 mil annuity or roughly $85 mil cash payout after taxes). I'll call you.

[JOSHHOEFER]

[QUOTE=Captkirkyota
75.00 The rear half has been beefed up stronger than stock. Needs a carrier bearing. You can get one from 20 - 80 bucks depending on where you call. I went thru it because my rear springs are really soft and have terrible axle wrap. Did not know this till after I went to a one piece otherwise I would have shortened the front when I put in my crawler.[/QUOTE]

What's the length? Probably won't fit mine.

[Captkirkyota]

What's the length? Probably won't fit mine.
Stock length, I had it on when I was swapped for almost a year. My axle wrap was causing me to blow out the carrier bearing, when I went with some other truck mods I went to a 1 piece. I wish I knew about the axle wrap so I could have kept this one, but mods I did used the area the carrier mounts up to.
If Mike ends up not getting it, your 1st in line.

[Heatstroke]

I want it. Either Tues/Wed daytime is fine. I'll give you a call.

[WARTOY]

http://img.photobucket.com/albums/v420/captkirkyota/temp/P2240001.jpg
75.00 The rear half has been beefed up stronger than stock. Needs a carrier bearing. You can get one from 20 - 80 bucks depending on where you call. I went thru it because my rear springs are really soft and have terrible axle wrap. Did not know this till after I went to a one piece otherwise I would have shortened the front when I put in my crawler.


oh, oh, oh pick me pick me!!! just kidding, i don't want it.. but i was wondering where you got your one piece drive shaft done, and how much did it cost you??? ;)

[Captkirkyota]

oh, oh, oh pick me pick me!!! just kidding, i don't want it.. but i was wondering where you got your one piece drive shaft done, and how much did it cost you??? ;)
I got it done at Precision DL in Phx. I have 2 an HD one made from .250 wall and a regular duty one. Don't remember what I paid.