most work needed before Take Over?

[Bear]

Of the members that are attending this year's Take Over, with just about 6 weeks away. Who has the most work to do on their rig before the event?

My laundry list starts with regearing my front axle with new gears since I busted up my "brand new" 5.38's (just after 5 runs)(and no, it wasn't because I was on the skinny too much)

Here is my list:
Fix front gears
clean up and repair O2 sensor wires
Grease carrier bearing
Fix Power steering pump leak
Buy spare tire

Welding
Install rear diff guard
Build hi-lift hold down
Build rear bumper
Build spare tire carrier
Add brush guard to sliders
Ubolt flip kit install

plus all the normal maintence such as fluid changes and such.

[NEV2DEP]

Wow you got me beat.Just need to get some bumpstop and get them mounted,get cb installed in den instead of just laying on seat and that little issuse with my pb cable which buy the way i think i have solution for.I'm just gonna move it behind the shocks and cut the cable supports off.Do we need to come down a week early and help ya get that thing ready to go?You better get off here and get to work.

[Bear]

Help is always good, but I think I got my stuff covered. Things like the rear bumper and modifying the sliders is really just optional stuff anyway. It would be nice to get it all done, but it won't keep me off the trails if you know what I mean.

If I am understanding you correctly on your PB cable. I saw that option, but I think it would be better to angle the shocks a bit as my original suggestion. But it is your truck, your choice and I am sure what ever you decide it will be a good choice.

Back to topic though. I hate this time of year! I always get preoccupied thinking about take over and what I need to do to my truck before the event!

I just remembered another task I need to complete…I need to move my rear axle as it is too far forward right now.

Hmmm maybe you should come down a week earlier so you can help me with the grinder. :saw: :lmao:

[Full_Tilt_Fud]

mine has to go to the body shop to get a fucked up prior repair re-done and then i need to armor it the best I can, add recovery points and do some general maintence.

[Bear]

So you barely fit into catagory two then? ;) Barely out of catagory one. :rofl:

[Full_Tilt_Fud]

Your right....as a matter of fact it is parked in a mall parking lot right now.

[Full_Tilt_Fud]

and I am standing at the counter of a service center.

[Bear]

Your right....as a matter of fact it is parked in a mall parking lot right now.

:rofl: :rofl: :rofl: :aahg:

[01 Tundra]

My Tundra is currently sitting on four jackstands looking like a big freak :rolleyes: ! My Stazworks rims are supposed to arrive next week (they have 4-1/2 of them complete with tires mounted, but are still waiting on one rock ring).

I also have no front axle on the truck right now. My Rockcrusher housing is supposed to be complete tomorrow, so I hope to be building it by the end of next week...........but then there's figuring out where the steering ram will live now, re-working the tie rod and drag link since my new axle will be 70" WMS - WMS, cutting of sheetmetal for the new 37's to clear, and the rest of the shakedown work required to be confident in this new set-up.......gonna be some long nights ahead for me :rolleyes: !

[Bear]

I have been quietly lerking in the shadows of the board watching everything you have been throwing at your truck. That damn thing is already a beast! there won't be anything safe after you are finished. It is truely going to be a work of art!

Sounds like you have a decent handle on things though, so in the infamous words…"git-r-done!"

But 70" WMS? One word…DAYUM!

[purity]

1. i need new skids to slap on (waiting for allpro to put em out for sale).
2. probably need to paint the skids as well.
3. also need some sliders to throw on.
4. a cb install and tune.
5. i want to plumb all my breathers to the air box.
6. fluids/greasing, general maintanence.
7. come up with new turn signals
8. new air filter might be needed by the end of july

lets see what else gets added to this list before july 20.
the wallet is curled up in a dark corner somewhere as i type this.:D

[Bear]

I genereally do all my fluid changes prior to big wheeling trips, although you could probably toss a coin as to which is best to do.

I think of it as I know I'll be driving the truck hard so the fresh stuffs gives me a feeling of protecting moving parts.

But I also always do an inspection after those same runs and if I feel it is needed, I'll change the fluids again! It might be a waste of money doing it this way, but I figure an ounce of prevention…

[01 Tundra]

Yeah, so.....................still waiting for my parts - it's always good to make major changes to your junk prior to having to drive 7-1/2 hrs to wheel the shiat out of it :rolleyes: !!!!!

http://img.photobucket.com/albums/v419/01tundra/CIMG0451.jpg

[Texan1983]

Need to fix my cb, locate a new t-case skid or fix the old skid row one, add longer shackels, and crank the front coils up alittle more, change fluids, and maybe (if i can find the money) get bigger tires. definatly doable if i can find the time to do it.

[KStacoma]

I"d love to get my sas done before takeover but I don't think it will happen :mad:

[jh3]

Chit......I'm trying to do my SAC before :confused: :confused: :confused: :confused: :confused: :confused: :confused: :confused: :confused: :confused: :confused: :confused:

[AVplus]

+ paint sliders and get them welded on
+ finish painting rear bumper (been wearing primer for 2 weeks now :rolleyes: )
+ install CB
+ install extended rear brake line (something thats been on my to-do list for about a month now, god i'm bad)
+ change oil and filters
+ fix sway bar connection (damn thing won't get tight and won't come loose, the clanking it causes has been driving me fuckin nuts)

i better light a fire under my ass and finish this list. i still want to paint my whole truck spray can style but i don't think i'll have my new custom diy paintjob ready in time ... i still can't pick a design.

[Intrepid]

I need to do the chevy swap, rears up front, hi-steer, fix the miss in the engine, cut the rear fenders, possibly herculine? :D

[NEV2DEP]

+ fix sway bar connection
just :saw: ya won't miss it.

[SAR_Squid79]

I wanted to get new Front and Rear tube bumpers before TakeOver, but now it's clear that THAT ain't gonna happen.

Now I'm just hoping I can finally get a full size spare by then.

However, I'm pretty sure that I'll have my new skid plate just in time for TakeOver :wink2:

[Captain J]

I need to install Body lift to stop the tire rubbing, if I can get my downeys rebuilt in time I will put those on, replace bed bar mounting bolts so it don't fall out, take diff drop off so I can put skid plate back on, and probably be about time to change fluids and grease everything...Might even take the BFH to the pinch welds. I did this when I had 31's but now I am sporting 33's and they were rather noisy at Gilmer this weekend.
I am also going to change all the fender flare bolts to pan head screws so the tires will slide over them better.

[ohio03trdtaco]

I don’t have much to do.
1. Oil change
2. Change oil in both diff’s
3. Repaint sliders ( ah maybe)
4. Install e-locker guard (yeah only been sitting in my garage for about 3 months)
5. Stare at dent in beside and hope I fixes it’s self because I don’t have the money to get it fixed.
6. Wash and wax, so it looks good in the mall parking lot again. :D

Well that is about it.

[99TanTaco]

just :saw: ya won't miss it.
yep, one of the best mods I've done

[Spacecwboy]

Replace CB coax
Repair Brakes
Move rear axle back 3/4"
Repair E-Locker
Fab up front Skid plate to match up to AP Bumper
Fab front tow hooks
New rear bumper?


and sooooo much more

[Bear]

However, I'm pretty sure that I'll have my new skid plate just in time for TakeOver :wink2:

Just make sure you have the bolts! I am pretty sure each and every bolt I had for it is in the bottom of a coffee can…no way in hell I'll have time to sort for them!

[98taco4x]

Finish Tube Doors
Finish Fixing the holes in the floorboards (done)
Install Body mount bushings (done)
Bedline inside of cab
Build Sliders
Build Front Bumpers (mount winch in front bumper)
Fix holes in the frame
make center consule
Bed rack to mount Spares, cooler, and highlift to
Install new Brakelines
Fab up a battery hold down bracket *Done*
Change fluids in the truck
Maybe finish grooving the other two tires on the truck.
Maybe make a rear bumper.
Maybe fix parking brake

Dayum I need to get busy :D

[Bear]

thanks for making me feel better about my list.LOL

[98taco4x]

HEHE I try
Good Thread Bear
Now I actually have a place were I can start to check stuff off as they get done.
Now I just need the time to work on them.

[Bear]

HEHE I try
Good Thread Bear
Now I actually have a place were I can start to check stuff off as they get done.
Now I just need the time to work on them.
thats providing that you get the stuff done! I am worried that I am not going to have the time myself!

I was going to do some work on the truck this weekend, and wouldn't you know it? one of the kids had a soccer tournament all weekend. Now I just have to figure out how to fit this last weekends agenda in with next weekends?

[98taco4x]

Almost same boat here. Had plans to work on it this past weekend and nothing else but we had an unexpected death in the family and that really took presedence (sp)

[Bear]

you never can anticipate something like that, sorry to hear about your loss though!

makes you sit back and see what really matters in life though!

Again sorry for your loss

[Bear]

I wish the damn event would hurry up and get here! I keep finding more crap I need to do to my truck!

Now the carrier is toast and I need a longer Ubolt since I added some shims to the front axle!

[99ARTaco]

1. receive my new All pro sliders.
2. Primer sliders.
3. Drink Beer.
4. Another coat of Primer.
5. Another beer.
6. First coat of paint on sliders.
7. Drink another beer.
8. Second Coat of paint.
9. Drink 3rd to last beer and consider making another beer run?
10. Drink the forth beer cause the thrid one went down so fast this time.
11. Third coat of paint.
12. Drink next to last beer.
13. Find a welder that can weld these bad boys on for me.
14. Drink my last beer, find a DD, and pick up another 6pack on the way to the welders.
15. watch the welder at work and ask him as many questions as possible so he doesn't try keep me there and drink my beer.


16. Go home and justify to the wife why I'm drunk and how the hell I paid for the sliders, beer and welder???

Anyone have a longer list then me?? Crap and my truck is totally stock, I bet those modified rigs have a huge list???

[Bear]

Yea! my list is much, much longer with my SAC'ed rig! and does not involve drinking and driving.

[99ARTaco]

yeah maybe i should have left that part out? You're right, drinking and driving is just plain stupid, I'm editing my original post now.

[01 Tundra]

Just got my new shoes today so I'm getting a little closer, axle was shipping out today which means I'm gonna be busy next week :rolleyes: !

http://img.photobucket.com/albums/v419/01tundra/CIMG0455.jpg

http://img.photobucket.com/albums/v419/01tundra/CIMG0454.jpg

[TacoCrazy]

Bad Ass!! Can't wait to see that beast in person..Hurry up Takeover!

[Bear]

Looking sweet!

[98taco4x]

Update. slowly starting to get things done.
Finish Tube Doors (done)
Finish Fixing the holes in the floorboards (done)
Install Body mount bushings (done)
Bedline inside of cab (Done)
Build Sliders (Done)
Build Front Bumpers (started)
Fix holes in the frame (started)
make center consule (Not enough time)
Bed rack to mount Spares, cooler, and highlift to (not enought time)
Install new Brakelines
Fab up a battery hold down bracket (Done)
Change fluids in the truck

Dayum I need to get busy :D

[Bear]

Dayum I need to get busy :D
At least you are working on your list. I think I am dragging my heels more than doing anything!

I did take my driveshaft in this morning for a new carrier bearing…and finally replaced my passengers side seatbelt ( I have had the replacement sitting in my garage for almost 3 months)

But I don't think either one of those items was actually on my list :doh: so I still have a lot to get busy on! Hopefully be ordering my new gears for the front axle tomorrow though! then I will feel productive again!

[98taco4x]

only 4 weeks you need to get busy man. :D

[Bear]

only 4 weeks you need to get busy man. :D
I have a feeling that I am going to have to compromise…in other words, make sure that the important functional work gets done while the bling, non-important things such as the spare rack are going to be put on hold!

I mean it is like this. Do I need 4wd more than I need to bend tubing for the tire rack? do I need a dependable truck to get down there or bling rock guards for the trail?LOL

Know what I mean Vern?

The truck will be trail worthy again next week, so after that, what I get done will only be icing! and three weeks can be a long time! my concern is money.LOL!

I'll be ready I think!

[Valkyrie]

You need to quit posting & start wrenching son!

[Bear]

You need to quit posting & start wrenching son!
I might as well post since I can't wrench while at work! LOL

I would rather waste my time at work posting rather than thinking about all the wrenching I have to do

But I think I am still worrying about the wrenching even while I am posting.
Talk about self-defeating! LOL

I should be ready though! Are you trailering?

I am guessing you got that trailer delimma figured out with Jamie?

[Valkyrie]

The guy weasled out of the deal, but thanks for everyone's offers to help Phil out.

I don't trailer my junk. :D

[Bear]

I don't trailer my junk. :D
For some reason this statement seems to be an oxymoron or something!

I would never relate you to owning anything that resembled "junk"!

Normally everything of yours that I have seen has been top notch machinery!

(psst…I can almost taste the shiner now!! 4 weeks and counting!)

[Dick Foster]

You Texas folks seem to have an awful lot of trailer trouble. I've seem to have heard that trailer sob story from Shannon and John before. I'm thinkin it's high time you Texas boys manned up and drove your shit out here and quit makeing all them pussyfied trailer excuses. After all Ted has driven his shit all the way out here from Virgina and does Moab real regular. LOL

[cooper4x4]

I need to get 4.88 gears and a front locker installed and broken in.

[Bear]

I need to get 4.88 gears and a front locker installed and broken in.
huh? I thought you were all set! what happened to your gears now?

Welcome to the loney empty front diff club!

I should be an ex-member of the club come next Tuesday or so! ordering new 5.38's tomorrow. I just hope that my locker wasn't taken out by the bent pinion gear!

[cooper4x4]

Well I have had new gears in my living room for a year now and I just got an Aussie front locker and now I jsut need to get it all installed.

[Bear]

Well now I don't feel so bad, it only took me four months to replace my pass. side seat belt. It sat in it's box for that 4 months. the only thing I had longer was my axle.LOL 4years! not many can top that wait!

[99TanTaco]

huh? I thought you were all set! what happened to your gears now?

Welcome to the loney empty front diff club!

I should be an ex-member of the club come next Tuesday or so! ordering new 5.38's tomorrow. I just hope that my locker wasn't taken out by the bent pinion gear!
Can I join this club? I exploded my front R&P a couple of weeks ago, taking out the spider gears as well. I should have a new R&P, an Aussie (to replace the spiders) as well as a twin stick (to make steering my newly locked front easier) here waiting to be installed by the end of the week

[jh3]

Aussie (to replace the spiders) as well as a twin stick (to make steering my newly locked front easier) here waiting to be installed by the end of the week

I did all of these before I cut and its MONEY :) I was able to do just about everything the SFA guys were :D

-Josh

[01 Tundra]

You Texas folks seem to have an awful lot of trailer trouble. I've seem to have heard that trailer sob story from Shannon and John before. I'm thinkin it's high time you Texas boys manned up and drove your shit out here and quit makeing all them pussyfied trailer excuses. After all Ted has driven his shit all the way out here from Virgina and does Moab real regular. LOL

Damn trailer queens :D ! I better take that back, my shit will probably end up being drug out there on a trailer with no front axle - I'll just have to go real fawkin fast in a straight line on the Alcan's, maybe I need a supercharger for the 4.7L :rolleyes: !

[Dick Foster]

Are you coming out here from TN?

[Swamper]

You guys dont have anything on me ;)

1. Fab front and rear bumper and some sliders
2. Weld front and rear third's (truck is mainly off-road)
3. Install extended brake lines
4. Buy my Swamper's
5. Install header
6. Install roll bar and 5 lights
7. Install new seal's in the front axle
8. Install brake and turning lights on the bed (bobbed the bed)
9. Install my leafs
and last but def. not the least of my problems.......
10. Get it running!!! (engine wont start :dunno: )

Top that!

[travisheals]

GOOD LUCK, Swamper!!!

[Swamper]

haha yeah I know but by this time next week NUMBERS 2, 3, 5, 6, 7, 9, and 10 will be taken care of for sure and this wed's 4, and 8 should be taken care of the only one that will be a big pain is number 1 Speeddemon and I were planning on working on that one this past sunday but I got called from work with an emergency Water damage at 3am and dint get home till 10am...woke up till 3 and there went the whole day

[98taco4x]

I don't know jh3 just started his sac about a week ago and trying to get it done before TO. He pretty much wins in my book.

[Bear]

That is pretty adventersome! I wanted to make sure and get my done over the winter so I would have all spring to test things out before T.O…glad I did because I am still finding minor bugs.

I keep butting heads against the wall with my drive shaft! I fixed my carrier, replaced a ujoint and now I have to go back into it because I didnt' notice the shop that built the carrier, got it out of phase by rotating the flange!

That and a new big screen TV has slowed me down! But I am making progress. got the brackets for the hi-lift welded up, just have to figure mounting points which is no biggy!

[Swamper]

I don't know jh3 just started his sac about a week ago and trying to get it done before TO. He pretty much wins in my book.


Yeah thats brave....I dont know if I would do that id have to give it some time to figure out all the bugs like Bear said

[98taco4x]

Well I know jh3 has done his homework and he has got 3 other members with Sac'ed tacos helping him. And from the last I saw he was about ready to put the front axle under there. He has a thread started in the SAS section.

[Bear]

The whole topic of Jh3 doing his SAS has got me wondering, especially since I know another member trying to get his done before take over.

What was the largerst number to date of SAS rigs at Take Over?

I have been to one Texas Take Over and one National Take Over and I think the largerst number at either one of those was like 3 or 4 sas rigs tops. I would guess this year we are going to have at least 9 or 10 maybe more. But I am sure that the year before last they easily topped that number being it was held in Tahoe.

[01 Tundra]

Still waiting on my f*@#ing axle damnit :mad: ! I keep hearing that it is shipped, but can't seem to get the tracking info on it, and considering it is air freighted in and should only take about six hours to make it to Nashville, the fawkin plane must have had to make a delivery in fawkin France first :mad: ! I am about to snap, why can't folks just shoot people straight instead of bull shitting them all the time...............ok, my blood pressure is now dropping back down so I feel all good again :rolleyes: .

I am going to fly to Parts Mike's place, kick his ass, and drive his damn Jeep to the fawkin Takeover if he doesn't get my shit here - this is so unlike him to do...WTF :confused:!

[jh3]

I am going to fly to Parts Mike's place, kick his ass, and drive his damn Jeep to the fawkin Takeover if he doesn't get my shit here - this is so unlike him to do...WTF :confused:!

Patiance danial son :D

[Dick Foster]

It would be a hell of a lot shorter to drive to the Rubicon and Fordyce from Parts Mike's house than to Takeover. May as well beat the shit out of that purdy Jeep of his on some good hard rocks and make it count. LOL

[Aleco911]

Alright so what do you guys think...

I gotta do the fluids
Check the power steering (might be a leak)
fix some dents for free...(gotta love hookups)

But majorly do you think I can get a Marlin trans in before takeover?... They have a two week lead time plus shipping. So IDK. I gotta order it by this month if I am going to do it. I would probably be breaking in the tranny on the way down to AK. bout 600 miles. Change the fluid, then change it again after I get back.

Possible?

[Valkyrie]

Alright so what do you guys think...

I gotta do the fluids
Check the power steering (might be a leak)
fix some dents for free...(gotta love hookups)

But majorly do you think I can get a Marlin trans in before takeover?... They have a two week lead time plus shipping. So IDK. I gotta order it by this month if I am going to do it. I would probably be breaking in the tranny on the way down to AK. bout 600 miles. Change the fluid, then change it again after I get back.

Possible?
Chop Chop! Quit posting here & send Marlin your credit card!

[Ricks72]

The whole topic of Jh3 doing his SAS has got me wondering, especially since I know another member trying to get his done before take over.

What was the largerst number to date of SAS rigs at Take Over?

I have been to one Texas Take Over and one National Take Over and I think the largerst number at either one of those was like 3 or 4 sas rigs tops. I would guess this year we are going to have at least 9 or 10 maybe more. But I am sure that the year before last they easily topped that number being it was held in Tahoe.
Would I be counted in this since my 4runner has an SAC. I'm going to say its going to be closer to 10-20, my guess 16 :)

[Aleco911]

hey valkyrie, can you hook me up with new clutch parts. I believe all the standard replaceables... clutch plate, pressure plate, throw out, anything else? Probably an alignment tool of sorts. Thanks.

[Valkyrie]

hey valkyrie, can you hook me up with new clutch parts. I believe all the standard replaceables... clutch plate, pressure plate, throw out, anything else? Probably an alignment tool of sorts. Thanks.
Sure, just email Barb or Jerald at info@trdparts4u.com and be sure to include your VIN...

[98taco4x]

I can think of 7 sfa, sac'ed toyota's from the TN Chapter alone that will be there.

[Bear]

I was just guessing.For all I know there might be more SAS rigs than IFS. Now that would be something!

So yoiu have 7 from TN, mine, Tacozilla, Chris King, right there alone is 10. and I know I don't everyone with an axle coming! I am sure there is going to be more!

[01 Tundra]

Patiance danial son :D

Alrighty then, Parts Mike is off my shit list now - the axle is supposed to be here tomorrow :D !

I'm also happy cause I picked up my next victim today, just got a 2002 4Runner limited - those heated leather seats are gonna go so nice with the full-width axles, beadlocks, dual cases, and all the other junk off my Tundra here in a few years. It's gonna be real purty :rolleyes: :saw: :welder: !

[01 Tundra]

I can think of 7 sfa, sac'ed toyota's from the TN Chapter alone that will be there.

Is mine one of the seven?

[01 Tundra]

Well, good news is all the shit that goes in the new axle housing is here.....bad news is BAX Global lost my fawkin housing in San Francisco somewhere and can't seem to find it, so much for guaranteed 2-day delivery :mad: !!!!! Now some homo is pimpin around San Fran with my axle under the front of their Isuzu Butttrooper....no offense to any of you who live in San Fran, are bi-curious, or drive Troopers.....no really :D !

Sooooo, I may be at the Takeover without the Tundra, good thing I just picked up my 4Runner....I'm thinking that maybe I need to do a little premature trimming on the Runner :rolleyes: ! Let's see.......

BEFORE:

http://img.photobucket.com/albums/v419/01tundra/CIMG0457.jpg

AND AFTER:

http://img.photobucket.com/albums/v419/01tundra/CIMG0458.jpg

ONCE AGAIN....BEFORE:

http://img.photobucket.com/albums/v419/01tundra/CIMG0457.jpg

AND AFTER:

http://img.photobucket.com/albums/v419/01tundra/CIMG0459.jpg

[Bear]

Well Damn! any solutions from the company you ordered the axle from? like maybe sending a second one and having the shipping company fit the shipping for it as well as their insurance covering the loss of the first one?

that is why they have insurance in the first place.

[Dick Foster]

Nah just put some studs in those new tires and let the damn thing clearance itself. LOL

[Ricks72]

Nah just put some studs in those new tires and let the damn thing clearance itself. LOL
X2 it would keep that COG nice and low :D

[01 Tundra]

Ha! They actually "think" they found it in a aircraft container in Kansas City and they "think" that they can get it to me on Monday. Apparently there were "other" priority shipments that had more "priority" than mine, I sure do wish I could get within arms reach of the jackass who made that call:mad: ! Anyways.....guaranteed 2nd day delivery in 7 days, now that's F*ing service BAX Global :clap: !

On another note, Parts Mike has already got tubes installed in a second housing just in case these idiots have indeed lost it.


Just remember kiddies......when you need something delivered several days later than promised.......just call Baxtard Global shipping company for all your shipping needs :rolleyes: !

[01 Tundra]

Well, no housing yet...but lots of cool parts to stare at :rolleyes: !

D-60 hub assemblies with Stainless Steel Brake Corp. rotors and Dedenbear D-60 knuckles:

http://img.photobucket.com/albums/v419/01tundra/CIMG0464.jpg

35-spline Superior D-60 axle, Parts Mike high steer arm, and my massive D-44 pinion shaft.....aka: weak link :rolleyes: !

http://img.photobucket.com/albums/v419/01tundra/CIMG0463.jpg

D-60 CTM bling:

http://img.photobucket.com/albums/v419/01tundra/CIMG0461.jpg

[SAR_Squid79]

I hope you get it all worked out in time for TO - I was looking forward to having sex with your SAC Tundra!

[Lunnzz]

I need to replace
all balljoints
all tie rod ends
pitman arm
idler arm
new shocks
fresh fluids in the tranny & transfer case
flush old brake fluid & clutch
turn rotors
adjust valves one more time
take it in for recall work
rebuild steering gear box
and I think thats about it I doubt any of this will get done but I'll be there regardless unless something comes up.

[jh3]

Well, no housing yet...but lots of cool parts to stare at :rolleyes: !



Coolman, now start putt'n some chit together. You got 3 weeks!

-Josh

[Ricks72]

:lmao: I hope you get it all worked out in time for TO - I was looking forward to having sex with your SAC Tundra!

[AVplus]

Update

+ paint sliders and get them welded on >>Done
+ finish painting rear bumper >>Done
+ install CB >>still need an antenna
+ install extended rear brake line >>i suck
+ change oil and filters >>happening this week
+ fix sway bar connection >> i agree guys, this mofo is gettin :saw: off

[98taco4x]

Is mine one of the seven?
Yeah I counted yours.

Me
01 Tundra
Duby08
dstrbdone
ratherbwheelin
jh3 (pending he gets done :D )
toyotacrawler


Still SAC's in the chapter that will not be there.
Chris
twistytaco
and probably some others that I can't remember.

[01 Tundra]

Progress, just a little trim work left to do.

http://img.photobucket.com/albums/v419/01tundra/CIMG0494.jpg

http://img.photobucket.com/albums/v419/01tundra/CIMG0495.jpg

http://img.photobucket.com/albums/v419/01tundra/CIMG0493.jpg

http://img.photobucket.com/albums/v419/01tundra/CIMG0496.jpg

[jh3]

Looks good man, you got me jealous again!

-Josh

[98taco4x]

I got to change my shorts now.

[01 Tundra]

It's alive! Got to take it out and hammer on it a little and all seems good.....can't wait 'till Thursday! Damn 37's feel like I'm cheating, now I'm jealous of all you dudes running 40's & 42's...........hmmm :rolleyes: !

http://img.photobucket.com/albums/v419/01tundra/c0510e43.jpg

http://img.photobucket.com/albums/v419/01tundra/d7294ad8.jpg

http://img.photobucket.com/albums/v419/01tundra/b2663c44.jpg

http://img.photobucket.com/albums/v419/01tundra/d2faef1b.jpg

http://img.photobucket.com/albums/v419/01tundra/40edb030.jpg

http://img.photobucket.com/albums/v419/01tundra/447d243f.jpg

[Bear]

Hey that is looking really good! Very nice indeed!

I hear you about the 37's, I love mine!