where to get powder coating?

gregers05 · 09-12-2006, 03:22 PM

i know i asked this before, i cant find the post where u guys gave me some places, but where would be a good place to get my bumper powder coated? and how much does it cost? also how long does it usually take? if i cant get it done this week, ill just rattle can it.

GaTaco · 09-12-2006, 05:03 PM

I used this place in alpharetta called performance cryogenics and they do good work. It took about a week. I'll try and find their number if you want to go that route.

gregers05 · 09-12-2006, 07:49 PM

Quote:

Originally Posted by GaTaco

I used this place in alpharetta called performance cryogenics and they do good work. It took about a week. I'll try and find their number if you want to go that route.

well i need it done before saturday, im probably just going to end up rattle can it and get it powder coated later when i have more time and money cause i called a few places and they said it would be around 150

Maddog096 · 09-12-2006, 09:45 PM

why do you want to powder coat it anyway?

With just rattle cans your touch-ups are as good as new.

Or you could just line-x it. Takes about half a day with all the prep work.

4inT100 · 09-12-2006, 09:48 PM

150 sounds about right. it was 40 for me to have my valve cover blasted and powder coated. took about 3 days.

Miller's Powdercoating off Arcado Rd in Lilburn

gregers05 · 09-12-2006, 11:56 PM

Quote:

Originally Posted by Maddog096

why do you want to powder coat it anyway?

With just rattle cans your touch-ups are as good as new.

Or you could just line-x it. Takes about half a day with all the prep work.

ill just rattle can it. line-x is a good idea but im sure its pricey and i want to spend as little as possible cause im tight on money

09-12-2006, 05:03 PM	#2
GaTaco Senior Member Join Date: Sep 2005 Location: Athens, GA Posts: 425	I used this place in alpharetta called performance cryogenics and they do good work. It took about a week. I'll try and find their number if you want to go that route. __________________ 2000 Tacoma V6 4X4 5spd: All-Pro coilovers & upper a arms, 1" diff drop, All-Pro rear 3" springs, inverted 10" Bilstein 5100s, All-Pro sliders, ARB Bullbar w/ Tabor 9k winch, Front Range Rear Bumper, 33x10.50 BFG Mud Terrains

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Metal Powder Coating in Cincy?	HoT_DoGgIN	Fabrication/Tools	5	05-06-2006 11:33 PM
Powder Coating	Paul	Pickup/4Runner Tech	4	07-01-2005 07:42 PM
Powder Coating	TACORICAN	Early Tacoma Tech	2	03-23-2005 01:02 PM
Powder coat question	Maxwell	Early Tacoma Tech	3	02-24-2005 11:27 AM
best paint for sliders	chasintail	Early Tacoma Tech	29	01-15-2005 11:32 AM

09-12-2006, 09:45 PM	#4
Maddog096 Veteran Newbie Join Date: Dec 2004 Location: Atlanta, GA Posts: 601	why do you want to powder coat it anyway? With just rattle cans your touch-ups are as good as new. Or you could just line-x it. Takes about half a day with all the prep work.