From Faq

Vehicle Information:

• 1996 Toyota Tacoma
• Manual transmission
• 4WD 3.4L V6
• 74,000 miles

These are basic instructions on how to replace clutch pedal turnover bushing.

If you have any questions about this write-up visit Lieblweb.com and e-mail us!

It's not uncommon to replace this bushing once every year depending on your driving. I've replaced mine twice so far.

Contents 1 Troubleshooting 2 Parts Needed & Other Information 3 Tools Needed 4 Description & Location

Troubleshooting

On Toyota Tacoma trucks equipped with manual transmissions, a squeek or grind is often heard when pushing down on the clutch pedal. This squeek or grind can also be confused with another clutch related problem - so please make sure you are performing the proper repair for the problem you are encountering. Take time to read the information below- and you should be able to take a look at your current clutch pedal turnover bushing and make a decision if it needs to be replaced.

Parts Needed & Other Information

• Toyota Part #90389-05017.
  • Please make note - this part is for the vehicle listed above. Make sure when ordering any parts that they are specific to YOUR application.

Tools Needed

• 12mm socket with extensions,
• Workbench equipped with a VICE,
• Needlenose pliers may be needed,
• Safety glasses recommended
• Other tools may be necessary.

Description & Location

The clutch pedal is mounted on a large bracket assembly. The entire bracket assembly will need to be removed to perform the final repairs.

1. Remove the cotter pin from the clutch shaft roll pin as seen in the picture. After removing the cotter pin, remove the roll pin. This will free the clutch shaft from the pedal assembly.
   

   

   Cable Adjustment Assembly
2. Unplug both electronic clutch pedal sensing devices - as seen in the picture.
   

   

   Cable Adjustment Assembly
3. Remove the top bolt (as seen in the picture) using a 12mm socket with extension.
   

   

   Cable Adjustment Assembly
4. Open up your hood and look in the upper right corner. This is your clutch master cylinder where the hydraulic fluid is stored. Remove the 2 nuts as seen here. The master cylinder will remain in it's position even after you remove it's mounting nuts/studs.
   

   

   Cable Adjustment Assembly
5. Go back inside the cab of the truck and gently pull the entire clutch pedal assembly. Be careful of the wires and other parts in the area.
   

   

   Cable Adjustment Assembly
6. You'll want to secure the Clutch assembly in a vice by clamping on the pedal. BE CAREFUL when handling this assembly. The spring has a lot of potential force. The pedal can move positions and if you're not careful, you could pinch yourself unexpectedly.
   The new bushing fits inbetween the spring and the clutch pivot arm (as seen in the picture). It is a horse-shoe shaped part that will snap into place.
   As you can see here, the original bushing is completely gone and the forces have began to wear away at the metal.
   

   

   Cable Adjustment Assembly
   This is a picture of what the new bushing looks like. It is very very small.
   

   

   Cable Adjustment Assembly
7. CAUTION! Wear safety glasses!!
   You'll want to put the central spring arm (where the bushing is placed) at its lowest position. This will help remove some of the spring tension. Remember - the spring has a lot of stored energy (forces). If you are not careful, it can snap and cause injury!
   By taking a long screwdriver or some type of prying device, pry one end of the spring out of its spring seats. You should be able to remove the other side rather easily now that the spring is no longer under tension.
   Take notice to the exact position of the spring when it is removed. You will need to install it in the exact way as it came off.
   

   

   Cable Adjustment Assembly
8. Install New Bushing: Now that you've got that spring out of the way, you can easily install the new bushing. I decided to add some grease to the bushing before installation.
   I also added some grease to the spring seats.
   

   

   Cable Adjustment Assembly
9. Remember to install the spring in the exact position it was when you removed it.
   First, insert one side of the spring into its spring seat. Then, insert the center spring piece into the new bushing. This may take a little bit of muscle and some prying.
   Finally, with some prying - try to compress the spring enough to get the spring into the other spring seat.
   
   Again, be very careful with the spring. You will be applying pressure (adding tension) to the spring in order to finish the installation. If you slip just a little, that spring tension will let go and could cause injury.
   
   Take the entire assembly and gently maneuver it back into the cab - in reverse order in which you removed it. Once you get the assembly in the cab area - I would install the top bolt first (hand tight) to hold the entire assembly in place while you are working outside the cab and under the hood. Tighten the bolts down while you are still under the hood. Go back into the cab and tighten down the bolt at the top. Plug in your electronic sensing devices and install the clutch shaft onto the clutch pedal with the pin and cotter pin.
   

   

   Cable Adjustment Assembly

---

Back to Maintenance Information

Back to the Main Page