TTORA Forum banner

1 - 10 of 10 Posts

·
Registered
Joined
·
81 Posts
Discussion Starter #1
Hi,

I'm looking to buy a set of brand new 16x8 TRD Alloy Ivan Stewart Edition on ebay. Does 690$ with caps and lug nuts is a good deal? Can I expect to get better, mean lower, somewhere else? Will I be able to fit 285x75R16 on a Tundra? (Especially looking for good advices on clearance near upper a-arm) I'm a proud owner of a Tacoma. It's for my daddy :D :D

Thanks for any helpful info.
 

·
Registered
Joined
·
114 Posts
Sounds like a pretty good deal to me... I haven't priced them in awhile but last time I saw them on-line it was more like $900. Good luck!

J
 

·
Registered
Joined
·
55 Posts
You can buy them direct from the company. TRD I believe only changes the center cap, but they have this other company make them. I forgot of the name of the company
 

·
Premium Member
Joined
·
373 Posts
ibidu1 said:
You can buy them direct from the company. TRD I believe only changes the center cap, but they have this other company make them. I forgot of the name of the company

Niche? I think they only sell them in 17" or larger.
 

·
Registered
Joined
·
598 Posts
phand00 said:
Hi,

I'm looking to buy a set of brand new 16x8 TRD Alloy Ivan Stewart Edition on ebay. Does 690$ with caps and lug nuts is a good deal? Can I expect to get better, mean lower, somewhere else? Will I be able to fit 285x75R16 on a Tundra? (Especially looking for good advices on clearance near upper a-arm) I'm a proud owner of a Tacoma. It's for my daddy :D :D

Thanks for any helpful info.
Are you asking if you can clear metric 33's on a tundra with stock suspension?
 

·
Registered
Joined
·
81 Posts
Discussion Starter #7
I'm asking if I can clear metric 33's on a tundra with small suspension lift. Surely won't fit stock? :D I would like to be sure I can put thoses 33's without hurting the upper arm.

Thanks
 

·
Registered
Joined
·
32 Posts
Without a lift you should clear the upper-a-arm but will rub front and rear of fender when you turn. 2.5" lift barely clears it on flat turning, any compression such as drive ways and drrrrrrrr. You know that sound.
 

·
Registered
Joined
·
114 Posts
Anybody know for sure what company makes them??? I would like to check into that... I would love to have a pair of those in a 10" width if possible? I love them but, do not want 8's

MUST HAVE 10" WHEELS!!!! (in a slooow deeep voice)

Later,

J
 

·
Registered
Joined
·
11 Posts
phand00 said:
Hi,

I'm looking to buy a set of brand new 16x8 TRD Alloy Ivan Stewart Edition on ebay. Does 690$ with caps and lug nuts is a good deal? Can I expect to get better, mean lower, somewhere else? Will I be able to fit 285x75R16 on a Tundra? (Especially looking for good advices on clearance near upper a-arm) I'm a proud owner of a Tacoma. It's for my daddy :D :D

Thanks for any helpful info.

Just FYI,

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1&item=7934994224&ssPageName=STRK:MEWN:IT





05AZTaco
 
1 - 10 of 10 Posts
About this Discussion
9 Replies
7 Participants
AZ05Taco
TTORA Forum
TTORA forum is the best Toyota off-road club around. We are nation wide with chapters in most states. Come in and discuss Tacoma, 4Runner, Highlander, & TRD models.
Full Forum Listing
Top